Penyusunan Jobsheet Kendali Motor Servo Berbasis Human Machine Interface
##plugins.themes.academic_pro.article.sidebar##
##plugins.themes.academic_pro.article.main##
Abstract
One of the Practice courses for the D3 Electrical Engineering study program at the Electrical Engineering Department is Electrical Machine Control Practice. One of the materials given in this Electric Machine Control Practice is servo motor control. Along with technological developments, in the electrical energy conversion laboratory as a place for Electrical Machine Control Practice, a servo motor control training kit is available using a Programmable Logic Controller (PLC) and Human Machine Interface (HMI). Based on the observations made, the PLC and HMI-based servo motor control training kit does not yet have a manual or jobsheet as a guide for students and lecturers in carrying out practical activities. Therefore, in this study it is proposed to make a servo motor control jobsheet based on PLC and HMI using the Siemen S7 1200 PLC training kit with a Sinamic V90 servo motor driver and HMI TP 700 Comfort. The feasibility of the jobsheet is assessed from the validity, practicality and effectiveness tests with research procedures following the 4D development research method, which consists of the stages of define, design, development and dissemination stages. Based on the results of the tests carried out, the validity test results are obtained in the very valid category, the practicality test results are in the very practical category and the effectiveness test results are in the effective category. So that the jobsheet can be considered feasible to be used as a guide in implementing PLC and HMI-based servo motor control practices.
##plugins.themes.academic_pro.article.details##
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
[2] F. Setyawan dan B. Suprianto, “Pengembangan Trainer Dan Job-Sheet Plc Sebagai Media Pembelajaran Pada Mata Diklat Plc Di Jurusan Elektronika Industri Smk Negeri 2 Lamongan,” no. 5, hal. 509–515, 2014.
[3] L. Oktavia dan M. Yuhendri, “Pengembangan Jobsheet pada Proses Pembelajaran Praktek Mesin Listrik untuk Mahasiswa Teknik Elektro,” J. Pendidik. Tek. Elektro, vol. 03, no. 02, hal. 18–23, 2022.
[4] T. H. T. Maryadi, H. S. Pramono, Y. I. Hatmojo, E. Prianto, dan Sunomo, “Development of Human Machine Interface (HMI) Training Kit as A Learning Media for Industrial Automation Engineering Practical Courses,” J. Phys. Conf. Ser., vol. 1737, no. 1, 2021.
[5] S. O. Pratama dan M. Yuhendri, “Pengembangan Modul Kerja Bengkel dan Gambar Teknik untuk Sekolah Menengah Kejuruan,” J. Pendidik. Tek. Elektro, vol. 1, no. 1, hal. 62–66, 2020.
[6] F. A. K. Yudha dan B. Riyanta, “Perancangan dan Simulasi Trainer Human Machine Interface (HMI) untuk media pembelajaran berbasis CX Designer PLC,” JMPM (Jurnal Mater. dan Proses Manufaktur), vol. 4, no. 2, hal. 136–145, 2020.
[7] P. Chauhan, N. Nayak, J. U. I. Trivedi, dan V. Nayak, “Industrial Motor Controlling Using PLC, HMI Screen and Web Page,” J. Emerg. Technol. Innov. Res., vol. 5, no. 7, hal. 194–198, 2018.
[8] H. Haryanto dan S. Hidayat, “Perancangan HMI (Human Machine Interface) Untuk Pengendalian Kecepatan Motor DC,” Setrum Sist. Kendali-Tenaga-elektronika-telekomunikasi-komputer, vol. 1, no. 2, hal. 58, 2016.
[9] Y. Song, S. Cai, L. Yang, G. Li, W. Wu, dan L. Xie, “A Practical EEG-Based Human-Machine Interface to Online Control an Upper-Limb Assist Robot,” Front. Neurorobot., vol. 14, no. July, hal. 1–13, 2020.
[10] Joko, F. Akhmad, dan A. A. P. Putra, “Development of IoT-Based and Project-Based Learning Human Machine Interface Learning Media to Improve Ability, Innovative Behavior, and Skill of Industrial 4.0 and Society 5.0 Students,” Eurasian J. Educ. Res., vol. 2022.
[11] F. Azizah dan M. Yuhendri, “Solar Panel Monitoring and Control System Using Human Machine Interface,” Andalasian Int. J. Appl. Sci. Eng. Technol., vol. 2, no. 03, hal. 149–158, 2022.
[12] T. F. Azizah dan P. W. Rusimamto, “Perancangan Pembuatan Job Sheet Human Machine Interface ( HMI) pada Mata Pelajaran Instalasi Motor Listrik Di SMK Krian 1 Sidoarjo,” J. Pendidik. Tek. Elektro, vol. 8, no. 3, hal. 413–420, 2019.
[13] R. Jannah dan M. Yuhendri, “Pembuatan Jobsheet Kendali Motor Induksi menggunakan Human Machine Interface,” J. Pendidik. Tek. Elektro, vol. 03, no. 02, hal. 184–191, 2022.
[14] I. Rifaldo dan M. Yuhendri, “Sistem Monitoring Kecepatan Motor Induksi dengan HMI Berbasis PLC,” JTEIN J. Tek. Elektro Indones., vol. 3, no. 2, hal. 319–325, 2022.
[15] Y. Sang, F. Li, Y. Dai, dan F. Duan, “The practical control technology design for AC servo motor based on STM32 micro-controller,” Proc. 2015 IEEE Adv. Inf. Technol. Electron. Autom. Control Conf. IAEAC 2015, hal. 1–5, 2016.
[16] F. Dames dan D. T. P. Yanto, “Sistem Kendali dan Monitoring Kecepatan Motor Servo Berbasis Human Machine Interface,” JTEIN J. Tek. Elektro Indones., vol. 3, no. 2, hal. 487–495, 2022.
[17] L. Hirzan dan M. Yuhendri, “Pengembangan E-Modul Mata Pelajaran Instalasi Penerangan Listrik untuk Pembelajaran Daring,” J. Pendidik. Tek. Elektro, vol. 1, no. 1, hal. 142–146, 2020.
[18] Z. Shidqon As-Sholhy, T. Wrahatnolo, Joko, dan B. Suprianto, “Pengembangan Job Sheet Trainer Otomasi Instalasi Tenaga Listrik Menggunakan Plc Omron Cp1e E20sdra Di Smk Negeri 2 Surabaya.”
[19] R. Fadli dan M. Yuhendri, “Pengembangan Jobsheet Trainer Motor Listrik di Sekolah Menengah Kejuruan,” vol. 01, no. 01, hal. 38–42, 2020.
[20] M. Yuhendri dan S. P. P, “Media Pembelajaran dengan Powerpoint Sebagai Instrumen Pembelajaran untuk Sekolah Menengah Kejuruan,” J. Pendidik. Tek. Elektro, vol. 1, no. 1, hal. 109–113, 2020.
[21] S. Harowanti dan M. Yuhendri, “Pengembangan Lembar Kerja Peserta Didik Berbasis Masalah pada Pembelajaran Pemograman Mikroprosesor dan Mikrokontroler,” J. Pendidik. Tek. Elektro, vol. 2, no. 1, hal. 6–9, 20212.
[22] R. P. Mayenti dan M. Yuhendri, “Pengembangan E-Modul Dasar Listrik dan Elektronika di Sekolah Menengah Kejuruan,” J. Pendidik. Tek. Elektro, vol. 2, no. 1, hal. 10–13, 2021.